Skip to content
Specialized Wolf repair service. Experienced technicians, genuine parts, service across major U.S. metro areas.
Error Code

Wolf Wall Oven Error Code 10 0 0: UIM Communications Error

Error code 10 0 0
Appliance Wall Oven
Quick answer

Wolf lists a breaker reset first for the 10 0 0 UIM communications error.

Error-code meanings can vary by Wolf product type, series, and model. Confirm the code against the documentation for your exact model before using troubleshooting information. Record your full model number before acting. Code shown: 10 0 0.

Plain language

What this code means

Wolf reports a communications error detected by the user interface module.

According to Wolf’s Legacy E Series answer, 10 0 0 means a communications error was detected by the UIM (user interface module). That unit lives behind the touch pad; it reads each press and shows the replies.

At a glance

Code 10 0 0
What it means Wolf reports a communications error detected by the user interface module.
What you can check Cut power at the oven's breaker for 30 seconds, restore it, and try the oven. If it works without more errors, no action is needed, and a one-time glitch needs no follow-up.
When to call a technician A code that returns, particularly at the start of every cycle, arrange a service visit to diagnose and repair the oven. Note whether the keypad responds when you call.

The reset in short

  • Breaker for the oven off, 30 seconds.
  • Breaker on again.
  • Try the oven. If it works without more errors, Wolf requires no action.

If it returns

Wolf says a returning code needs service to diagnose and repair the oven. Its article gives no list of causes and no part to replace, so home checks end with the reset. A one-time glitch that clears needs no follow-up; a repeat, particularly at the start of every cycle, is the signal to arrange a visit.

Common questions

Does 10 0 0 mean the touch pad has failed?
Not according to Wolf, which says only that a communications error was detected. A separate article, “Wolf Touch Pad or Controls Not Working,” covers controls that do not respond.

Must I call if it clears?
If the oven runs without further errors after the reset, Wolf says no action is required.

How do a fault and dead controls differ?
They can feel the same at the oven, yet Wolf lists them as two topics. A code that keeps recurring, or shows at every cycle start, is a reason to book service.

How much Wolf says

The article for 10 0 0 is short and holds one real instruction, the breaker reset above.

Similar codes

  • 08 0 1 is a keypad-side communication fault
  • 07 0 28 is a touch pad communication fault

Wolf oven service in Miami, New York, Houston, Los Angeles and San Diego

Wolf wall oven service covers the Miami, New York, Houston, Los Angeles and San Diego metro areas. Call (844) 886-0581 if 10 0 0 persists, and have the code, the model number from the data label and whether the keypad responds. The Wolf oven service page gives more.

Source: Wolf Legacy E Series (SO24) wall oven error/fault code answer pages

Important safety warning. Do not attempt repairs involving electrical components, gas, water lines, refrigerant or sealed systems. Unplug the appliance if it is safe to reach the outlet, and leave internal diagnostics to a qualified technician.

Seeing this code on your Wolf appliance?

Book a specialist visit for a clear estimate and approval before any repair.

Ready to get your Wolf appliance working again?

Book a repair online or call us — clear estimates, approval before any work, and a workmanship warranty on completed repairs.

Book a repair

Tell us what’s wrong — we’ll take it from there

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area Serving Miami, New York, Houston, Los Angeles and San Diego metro areas.
Response time Same-day and next-day appointments in most areas.
Call Book a Repair